Gas Transmitter 3 Wire NH3 Transmitter. Detection range and output could be chosen with switches in the field.
Gas Detectors
Gas Transmitter 3 Wire NH3 Transmitter. Detection range and output could be chosen with switches in the field.
Gas Transmitter 3 Wire NH3 Transmitter. Detection range and output could be chosen with switches in the field.
Gas Transmitter 3 Wire NH3 Transmitter. Detection range and output could be chosen with switches in the field.
Gas Transmitter 3 Wire NH3 Transmitter. Detection range and output could be chosen with switches in the field.
Gas Transmitter 3 Wire NH3 Transmitter. Detection range and output could be chosen with switches in the field.
Gas Transmitter 3 Wire NH3 Transmitter. Detection range and output could be chosen with switches in the field.
The CD-700(CO2) transmitter can measure NDIR CO2 concentration, temperature, and
humidity. CO2 ventilation and temperature control can be controlled through up to two
relays.
For customer convenience, various outputs such as RS-485Modbus communication and
analog voltage/current are optional supported.
Available in toxic and oxygen formats.
The CD-700(CO2) transmitter can measure NDIR CO2 concentration, temperature, and
humidity. CO2 ventilation and temperature control can be controlled through up to two
relays.
For customer convenience, various outputs such as RS-485Modbus communication and
analog voltage/current are optional supported.
Available in toxic and oxygen formats.
The CD-700(CO2) transmitter can measure NDIR CO2 concentration, temperature, and
humidity. CO2 ventilation and temperature control can be controlled through up to two
relays.
For customer convenience, various outputs such as RS-485Modbus communication and
analog voltage/current are optional supported.
Available in toxic and oxygen formats.
The CD-700(CO2) transmitter can measure NDIR CO2 concentration, temperature, and
humidity. CO2 ventilation and temperature control can be controlled through up to two
relays.
For customer convenience, various outputs such as RS-485Modbus communication and
analog voltage/current are optional supported.
Available in toxic and oxygen formats.
The CD-700(CO2) transmitter can measure NDIR CO2 concentration, temperature, and
humidity. CO2 ventilation and temperature control can be controlled through up to two
relays.
For customer convenience, various outputs such as RS-485Modbus communication and
analog voltage/current are optional supported.
Available in toxic and oxygen formats.
The CD-700(CO2) transmitter can measure NDIR CO2 concentration, temperature, and
humidity. CO2 ventilation and temperature control can be controlled through up to two
relays.
For customer convenience, various outputs such as RS-485Modbus communication and
analog voltage/current are optional supported.
Available in toxic and oxygen formats.
The CD-700(CO2) transmitter can measure NDIR CO2 concentration, temperature, and
humidity. CO2 ventilation and temperature control can be controlled through up to two
relays.
For customer convenience, various outputs such as RS-485Modbus communication and
analog voltage/current are optional supported.
Available in toxic and oxygen formats.
Learn more about each of our gas sensor transmitters, including the gases measured, typical applications, and more. Please contact Airwave or your
distributor if you need to measure a gas not listed or need a different measurement range.
The Protec II (SAS) is a “Stand Alone” remote sensing system for toxic gases. it is intended to be placed in the area where leaks of these potentially dangerous gases are likely to occur. The protec II sensors measures the levels of these gases, activates alarms based on the concentration, and can transmit a signal to the appropriate control device
The AE4050 monitor is a single channel gas detection system featuring Lo and Hi adjustable alarm points that are normally set at 50 ppm and 100 ppm respectively. The alarm activates separate 5 amp relays which can turn on various electrical devices such as fans or warning lights.
The Protec II (SAS) is a “Stand Alone” remote sensing system for toxic gases. it is intended to be placed in the area where leaks of these potentially dangerous gases are likely to occur. The protec II sensors measures the levels of these gases, activates alarms based on the concentration, and can transmit a signal to the appropriate control device
The Intellisense is a “stand-alone” remote sensing gas detector for toxic or combustible gases (Ex). It is intended to be placed in the area where leaks of these potential dangerous gases are likely to occur. The Intellisense measures the levels of these gases, activates alarm relays based on the concentration, and transmits an analog or digital signal to the appropriate control device.
The Model 4001 System Controllers provide concentration display, alarm activation, and power supply functions for field mounted gas sensing devices. The system controller works in conjunction with any 4 – 20 mA Sensing Head for monitoring a wide variety of toxic and combustible gases.